ASTM F593 PDF

What are the differences between F and A stainless steel F bolts require ASTM F hex nuts in the matching stainless steel type. or visit us at ASTM F Scope – This specification covers the chemical and mechanical requirements for stainless steel. ASTM F specifications covers chemical and mechanical requirements for stainless steel bolts, hex cap screws and studs ranging from 1/4 to /2.

Author: Arashinris Tumuro
Country: Oman
Language: English (Spanish)
Genre: Education
Published (Last): 7 November 2005
Pages: 79
PDF File Size: 20.37 Mb
ePub File Size: 9.70 Mb
ISBN: 352-4-96276-545-9
Downloads: 62393
Price: Free* [*Free Regsitration Required]
Uploader: Tosho

Leave this field empty.

SH – Machined from strain hardened stock v593 cold worked to develop the specific properties. There are also additional testing requirements for Astk which are not required under the A specification. Hex head, square head and hex socket cap screws. The mechanical properties for these two alloy groups are listed below. The fasteners under the ASTM A specification are designed to be used in high temperature or high pressure service, often in flanges and piping systems.

In order to understand these dissimilarities there are overviews of each specification below followed atm a short asrm of these variances. What are the differences between F and A stainless steel headed bolts? Special fasteners have full size heads shall be tested as specified for stud bolts and other bolts.

Your email address will not be published. A – Machined from annealed or solution annealed stock thus retaining the properties of the original material; or hot formed and solution annealed. One primary difference between A and F hot-forged bolts is that F requires an additional test for susceptibility to intergranular corrosion, which the A specification does not.

Leave a Reply Cancel reply Your email address will not be published. A Where options are given, all the tests under an option shall be performed.

  BENTEL J424-8 PDF

ASTM F Specification – Boltport Fasteners LLP

There are multiple differences between these two specifications. Hot-forged headed stainless steel bolts under the A specification require solution annealing after forging to restore full corrosion-resistant properties. This specification covers the requirements for stainless steel bolts, hex cap screws, and stud bolts in imperial size 0. D Yield strength is the stress at which an offset of 0. AF – Headed and rolled from annealed stock and then reannealed AH – Solution annealed and age hardened after forming CW – Headed and rolled from annealed stock thus acquiring a degree of cold work.

CW – Headed and rolled from annealed stock thus acquiring a degree of cold work.

ASTM F593 Specification

F When approved by the purchaser, alloys or Se may be furnished. Headed fasteners in this specification require a heavy hex pattern head unless otherwise specified. ASTM F covers seven groups of ff593 steel alloys, including twelve austenitic, two ferritic, four martensitic and one precitipitain hardening.

A Minimum values except where shown as maximum or as a range.

AF – Headed and rolled from annealed stock and then reannealed AH ashm Solution annealed and age hardened after forming. Option A tests should be made whenever feasible. Do you have a job that requires A or F stainless steel fasteners?

Hot-forged headed stainless steel bolts under the F specification are qstm to either Condition A or Condition CW which both require solution annealing after forging to restore full corrosion-resistant properties. D When approved by the purchaser, alloysSe, or XM1 may be furnished.

ASTM A193 vs ASTM F593

C The yield and tensile strength values for full size products shall be computed by dividing the yield and maximum tensile load value by the stress area for the product size and thread sizes determined in accordance with Test Methods F Give Portland Bolt a call — our experts are standing by to assist you with all of your stainless steel fastener needs.

  HORDES MK2 CARDS PDF

A Tensile stress areas are computed using the following formula: There are many differences between these two specifications. The headed bolts f53 the F specification require a standard hex head pattern as opposed to heavy hex unless otherwise specified.

B Tests atsm are not mandatory C Special fasteners are adtm fasteners with special configurations including drilled heads, reduced body, etc. B legend of conditions: The F specification is more of a general purpose stainless steel specification used in all different applications. There are varying mechanical properties between the two specifications along with configuration differences for headed bolts and varying thread pitch requirements. The A specification is designed for use in high-temperature, high-pressure applications whereas F is used as more of a generic, all-purpose use fastener.

ASTM F – 17 Standard Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs

E When approved by the purchaser, alloy F may be furnished. This test adds to both the cost and lead time to produce this grade of stainless headed bolt. A Unless otherwise specified on the inquiry and order, the choice of an alloy from within a group shall be at the discretion of the fastener manufacturer B See section 4.

If a scale-free bright finish is required, this must be specified in the purchase order.