LM Phase Locked Loop. The LM and LMC are general purpose phase locked loops containing a stable, highly linear voltage controlled oscillator for. Part Number: LM, Maunfacturer: National Semiconductor, Part Family: LM, File type: PDF, Document: Datasheet – semiconductor. The LM and LMC are general purpose phase locked loops containing a stable highly linear voltage controlled oscillator for low distortion FM.

Author: Malak Bazil
Country: Guinea-Bissau
Language: English (Spanish)
Genre: Medical
Published (Last): 17 December 2014
Pages: 100
PDF File Size: 19.60 Mb
ePub File Size: 13.44 Mb
ISBN: 284-7-72445-656-4
Downloads: 32032
Price: Free* [*Free Regsitration Required]
Uploader: Baktilar

Search the directory for faculty or staff members.

LM Datasheet(PDF) – National Semiconductor (TI)

The device mainly consists of two components, one is voltage controller oscillator and other is phase detector. The VCO darasheet increase or decrease the signal frequency depending of the fed voltage of amplifier. The input signal goes in to the phase detector along with VCO feedback and this phase detector compares whether both signal are in same phase or frequency.

Our People Search the directory for faculty or staff members. More complicated ones use edge-triggered flip-flops. Lock in range of pll. The lm CN is available from National Semiconductor.

If daatasheet are in phase or frequency the PD provides zero voltage output and if phase or frequency is present the PD provides positive output voltage. In the device pin 2 and pin3 are inputs where we can connect the input analog signal but usually pin 3 will be grounded and pin2 is used as input.


I need to use a lag-lead filter.

Prices are subject to change without notice. The sugestion above could fit your need with a lm IC. To see a list of open positions, click here. At this point I need an explanat. However, if you intend to change the beep sound proportional to hartbeat, a more precise way could be achieved using a very small uC.

Take a look at the datasheet for the 74HC Previous 1 2 Next. Spring Semester, Monday — Friday: When a signal is given at the input, the frequency of both input signal and the VCO output is compared. What equations can i use? Hi, I am designing a frequency multiplier five times with the lm PLL. In addition to supporting the various labs in the EL building, we also provide equipment and manual check-out and a wide range of electronic components for sale.

For digital signals you can use XOR gate and run output through rc filter.

From what I know the free running frequency should be in the center of the range. And I plan using lm on the receiver side. Datasheft have to use the lm chip.

Now consider no input is given, under such case the VCO will be in free running mode generating signal whose frequency is determined by the capacitor and resistor connected at the pin 8 and pin 9.

FSK demod using LM The data sheet can be found at. You can also see open positions in the department. Welcome to the ECE Store. I need to work out the values for C1, C2 and R2 if the cut off frequency is 1kHz.


Why do you need a replacement?

RF, Microwave, Antennas and Optics:: The device being cheap can be used in applications where cost is considered. I was wondering if anyone could help me. FSK demodulator with LM, 2 questions about the circuit What is the import.

Welcome to the ECE Store

This output voltage of PD is given to amplifier to amplify the datasyeet signal and the amplified voltage is given to VCO, which generates waveform whose frequency depends on magnitude of the given input voltage.

I will be using the op-amp for the Lo. Open Positions To see a list of open positions, click here. My input range is from Hz to Hz, which means my output range is Hz to Hz. TL — Programmable Reference Voltage. I need help selecting the free running fre.

I have attached datasheeet circuit confguration i plan to use below. Tags Phase Locked Loop. However this means that most likely my loop gain KoKd will be greater then the datasbeet of the timing capacitor Co and resistor Ro.


Why do we connect the 0. Help me configure lag-lead filter. I decided to design the transmitter side by a VCO. The circuit of a phase comparator both analog and digital.